Search Result

1 - 10 (23)
Version:  Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016  | Last modified: 23.09.2019
3 user(s) found this FAQ helpful

Question:

How can I transfer the license permanently to a new computer?
How can I temporarily transfer the license of a registered computer to a different computer?
How can I interchange the licenses of two registered computers?



Answer:

If you activated the license online by entering a Product Key, you can return the Product Key and then use it for a different computer. You can return and activate the license only if the computers have Internet access. The computer where you want to return or activate the license does not have to be online all the time. It is enough if it is online while you are returning or activating the license.


Returning a license
To return a license in online mode

  • Open the 'License settings' dialog box: Services application -> Utilities -> License settings
  • Write down the Product Key for the license you are returning.
  • Click License activationon the left. Then click the license you want to return.
  • Click Return license.


You can now activate the license on a different computer.


Activating a license
If you want to transfer the license permanently, you can activate a license while you are installing Allplan or after you have installed Allplan. By activating a license, you connect the license with the new or other computer. As a result, you can start Allplan on this computer.
If you want to transfer the license only temporarily, install Allplan as a viewer on the second computer and
activate the license later.

To activate the license during installation:
Start Setup and follow the instructions displayed.

  • In the 'Installation Option' dialog box, select the 'Enter Product Key' option and click 'Next'.
  • Enter your Product Key.
  • Click 'Activate license'.


To activate the license after installation:

  • Open the 'License settings' dialog box: Services application -> Utilities -> License settings
  • Click License activationon the left.
  • Enter your Product Key.
  • Click Activate license.



Here comes a practical example:

If you want to use a Product Key for running Allplan on two or more computers, you must use computer A to return the license before you can use this license with computer B. To return the license, open the Services application -> Utilities -> License settings -> Return license. If this computer always uses the same Product Key, you can find this Product Key in the box below License activation. This box always displays the last Product Key entered.

If you switch between several licenses, it is a good idea to save the Product Keys used in a text file on the desktop. This way, you can copy the Product Keys quickly and easily to the license settings.


Notes:

You can also find your Product Key in Allplan Connect. Go to http://connect.allplan.com/license
Click Profile -> License administration.
Only administrators can use this function.

Download PDF  FAQ_EN_Transferring_license_to_a_new_or_another_comp...
Version:  Allplan 2018 / Allplan 2017 / Allplan 2016 / Allplan 2015 / Allplan 2014 / Allplan 2013 / Allplan 2012 / Allplan 2011  | Last modified: 15.11.2017
1 user(s) found this FAQ helpful

Question:

How can I update cross-section catalogs or install country-specific cross-section catalogs in Allplan 2011 and later?



Answer:

To install and save cross-section catalogs in Allplan 2011 and later, select Tools -> Defaults -> Cross-Section Catalogs. A dialog box opens. You can find a folder symbol and a disk symbol at bottom left.

To install cross-section catalogs, use the folder symbol. Another dialog opens, where you can select the cross-section catalog file you want to install. Select the file to be installed and click "Open" to confirm. This installs the corresponding cross-section catalog, which you can now use in Allplan.
To install country-specific cross-section catalogs, select the "Ing" folder, which was created when you installed Allplan. You can find it in the Allplan installation path (e.g., c:\Nemetschek\Allplan 201x\New\Ing - more information on the Allplan installation path is provided below in the "Notes" section).
This folder includes the country-specify cross-section catalog files.

To save a custom cross-section catalog, use the disk symbol. Another dialog opens, where you can select any folder to save the cross-section catalogs currently used in Allplan.



Note:

To update cross-section catalogs, you may need administrator privileges. If necessary, log on as an administrator before you start the update.

To use the cross-section catalogs for a specific project only, set the path settings for the cross-section catalogs of this project to project before you install the cross-section catalogs. In Allplan, open the "File" menu and select "Open Project..." Click the corresponding project with the right mouse button. Select "Properties". A dialog box opens. In the "Path settings" area, set the "Bar and mesh cross-section catalogs" to "Project".

To determine the path where Allplan is installed, use the Services application and select Service -> Hotline Tools-> showcfg. The Services application window shows the path of the Allplan installation folder.

The following abbreviations are used for the country-specific cross-section catalogs in the file names (axyzqusr.txt):
aut Austria
bel Belgium
bra Brazil
bul Bulgaria
deu Germany
eng England
fra France
hol Holland
hrv Croatia
ita Italy
kor Korea
pol Poland
rum Romania
rus Russia
slk Slovakia
svn Slovenia
swi Switzerland
tch Czech Republic
ung Hungary
usa USA

Download PDF  FAQ_EN_Updating_cross-section_catalogs_(Allplan_2011...
Version:  Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016 / Allplan 2015 / Allplan 2014  | Last modified: 21.09.2018
4 user(s) found this FAQ helpful

Question:

How can I permanently change the path settings presented for selection in specific tools (save, import)?



Answer:

When you save, import and export elements or files, Allplan automatically proposes a specific folder where the data is saved or taken from.
You can specify which Allplan file type is saved in which folder. These folders are automatically presented in the "Save" dialog box of the relevant file type. However, you can change them at any time.

To set this proposed folder on an individual basis, do the following:
Select the Tools menu ->Options... -> Desktop environment(Allplan 2009 and earlier: Tools -> Options... -> Global Options-> "Settings"tab).

You can click thePAah setting sbutton to the right of Folders for savingto define defaults. You can choose Project, Private, Custom or Last for the path setting:

  • Project: the file type is saved in the current project (not available for NDW and NPL files).
  • Private: the file type is saved in the user's private project.
  • Custom: you can specify any folder for the file type. To select the folder, click the path displayed in the Folder column and enter a new path or click ... in the Browse column and select the path in a dialog box.
  • Last: the file type is saved in the path you selected last.
Download PDF  FAQ_EN_Default_path_settings.pdf
Version:  Allplan  | Last modified: 06.06.2019
1 user(s) found this FAQ helpful

Question:

Why is Allplan running so slow?


Answer:

Check the following points:

1. Current version
Make sure you work with the current Allplan version.

  • Do the following or ask your system administrator to do this:
    Open Allplan and click the ‘?’ icon in the upper right-hand corner. Click ‘Update Allplan’.
    Select 'Find now'. If Allplan finds updates or hotfixes, download the installation packages.
  • Deactivate the virus scanner while your are installing updates or hotfixes. This might require administrator privileges. Contact your system administrator if you have problems.
  • Right-click the Allplan icon on the desktop. A shortcut menu opens.
    Select ‘Run as administrator’ and click ‘Yes’ to confirm the following message.
    As a result, Windows security settings do not block the installation.



2. System requirements:
Check the hardware and software required for your Allplan computer.

2.a)Download and run the system test.
Check the notes.
https://www.allplan.com/de/system/systemvoraussetzungen/

2.b)Check the Allplan system requirements:
https://www.allplan.com/de/system/systemvoraussetzungen/

2.c)You can find information about graphics cards at
https://connect.allplan.com/de/support/grafikkarten.html

2.d)You can find server operating systems you can use for the central file storage of Allplan at
https://connect.allplan.com/en/faqid/20140924094923.html


3. Hotline tools:
Start the Services application, open the ‘Service’ menu and select ‘Hotline Tools’. To save your settings, select the following tools.

- savestd: Saves user defaults.
- savereg: Saves CAD registry settings.

Start the Services application, open the ‘Service’ menu and select the following ‘Hotline Tools’:

- cleanup: Initializes the display.
- cleanstd: Resets CAD defaults.
- cleanreg: Resets CAD registry settings.

Check whether this has solved the problems.
If this is not so, restore the settings you just saved. To do this, start the Services application, open the ‘Service’ menu and select the following ‘Hotline Tools’:
- reststd: Restores saved user defaults.
- restreg: Restores CAD registry settings.


4. Color scheme selected in Allplan:
Start Allplan, open the ‘View’ menu, point to ‘Toolbars’ and select ‘Customize User Interface’. Open the ‘Customize’ tab and set ‘Color scheme and icon design’ to ‘Windows’.


5. Check the availability of all projects that are not online (if you use Workgroup Manager):
Start Allplan, open the ‘File’ menu and select ‘New Project, Open Project’. Deactivate ‘Check availability of all offline projects’.


6. Virus scanner
Check whether an anti-virus program is running in the background of the computer or server.
If so, reduce protection to "programs only".

Scanning "all files" can take a long time, considerably slowing down your computer when you switch between projects or exit the program.
You can exclude the Allplan installation folders from real-time scanning.When you start the Services application, you can see a list of the folders to be excluded.
You can find more information at
https://connect.allplan.com/en/faqid/20091126145752.html
Changes in the settings of the virus scanner only come into effect when you re-start the computer.


7. Aero desktop effects
Deactivate the Aero desktop effects of Windows.
To do this, open the Control Panel, select ‘Ease of Access’ and go to the ‘Make things on the screen easier to see’ area.
Select the ‘Turn off all unnecessary animations (when possible)’ option.


8. Name resolution on the network
If Allplan takes several minutes to start, name resolution on the network may not work.
To check this, do the following:
Right-click the Windows Start Button, select ‘Run’, type in ‘cmd’, click OK, type in ‘Nslookup’ and press ENTER.
Go to the line following the > character, type in the name of the Allplan data server and press ENTER.
The reply starts with the name and address of the server providing name resolution.
You can find the name and address of the Allplan data server in the second group.
If problems occur, contact your network administrator and ask him or her to configure name resolution correctly.


9. Speed of Allplan projects
Check whether some Allplan projects are slower than other Allplan projects.
Start with the empty project and check whether it is slow too.
After this, select any other Allplan project.

If it is only the current project that is slow, the problem may be caused by the data of the current project.
In this case, the data of this project must be analyzed in detail.
Contact technical support.


10. Network: checking out Allplan using Workgroup Manager
If you use Allplan with Workgroup Manager, you can check whether the problems are caused by the network. To do this, check out the workstation with the project in question and use the project on the local Allplan workstation.
You can find detailed information on checking out an Allplan workstation using Workgroup Manager in the
Services application. Open the ‘Help’ and select ‘Workgroup Manager’.

After you have checked out the workstation, Allplan no longer accesses the central file storage of the server.
If this has solved the problems, they are caused by the network. In this case, the network must be checked in detail.
Contact your network administrator and ask him or her to do this.

If the project is still slow, the problem may be caused by the data of the current project.
In this case, the data of this project must be analyzed in detail.
Contact technical support.


11. Log files and system information files
If all the points above do not solve the problems, technical support requires more system information about the computer running Allplan.

  • So, we would be grateful if you could send us a support request (Allplan Hotinfo with Allplan logging).
    To create a support request, start the Services application, open the ‘Service’ menu and select ‘Create support request (Hotinfo)’.
    Several dialog boxes open. Select ‘Technical Support Allplan’ and ‘Enquiry with Allplan logging’. Enter all the data required. Finally, click ‘Finish’.
    Another dialog box opens, prompting you to start Allplan. Click the ‘Start Allplan’ button.
    Allplan starts, logging all processes.
    Try to reproduce the problem as exactly as possible.
    Exit Allplan as soon as possible, reducing the data in the log file to a minimum.
    Then click ‘Next’ to generate the support request with the log file.
    You can find more information about Hotinfo at
    https://connect.allplan.com/en/faqid/20140528094911.html
  • To analyze the Windows system environment, we would ask you to send us the logs created by Windows Event Viewer of your computer.
    To start Windows Event Viewer, right-click the Windows Start Button, select ‘Run’ and type in ‘eventvwr.msc’.
    You can also type in ‘Event Viewer’ in the search box of Windows. This displays the link file to the Windows event logs.
    Using Event Viewer, create *.evtx files for the application log and the system log in the ‘Windows Logs’ area and for the ‘Administrative Events’ log in the ‘Custom Views’ area.


Please send us the files.

Download PDF  FAQ_EN_Allplan_is_running_slow.pdf
Version:  Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016 / Allplan 2015  | Last modified: 20.09.2018
3 user(s) found this FAQ helpful

Note:

You can help the technical support team to process your request by generating a support request with the Hotinfo program and sending it to us.

The generated support request will help to avoid unnecessary questions and delays, as it automatically contains all necessary information pertinent to the problem in question.


Procedure:

The Hotinfo program is installed along with Allplan; you can start it over the following ways:
1. Start -> All Programs -> Nemetschek -> Allplan [version number] -> Hotinfo [version number].
2. Allplan -> ? -> Generate support request (Hotinfo)
3. Allmenu/Services -> Service -> Create Support request (Hotinfo)


Select the team with whom you wish to communicate:
Choose the relevant entry, for example, Technical Support Allplan. The email address of the selected team is entered automatically.

Select the areas on which you have questions:
Please select the question that is pertinent to your support request.
You only need to select question 2 when Allplan support is requesting it from you.

01. General inquiry
02. Inquiry with Allplan logging

Note on question 02:
If you have selected question "02. Inquiry with Allplan logging", you can start Allplan straight form the Hotinfo after the questions.
This will generate and attach a log (trace).
Start Allplan by clicking on the button “Start Allplan”
Carefully reproduce the problem – for example, perform the steps that lead to the failure.
Then click "Next" to generate the support request with the trace.
You can click the "Take screenshot" button at any time while Allplan is running in logging mode. This way, you can quickly and easily save any error messages that may be displayed.

Enter your contact address:
Please enter your name, telephone number and email address
so that the technical support team can contact you.

Please describe the problem:
Describe the problem in detail (for example, include the exact wording of error messages).

Select the files you want to attach to the email:
You can include additional files with important information such as damaged drawing files, NID files or other files.

Note:
These files are only attached to the email when you send the Hotinfo by clicking “Finish” -> Option “Start email program…" or send it to us over File -> Send Message...".
See note further down.

Create the screenshots you want to attach to the email:
You can use the "New screenshot" button to take screenshots of the entire screen and send them as a file attachment to the Hotinfo.

Note:
These files are only attached to the email when you send the Hotinfo by clicking “Finish” -> Option “Start email program…" or send it to us over File -> Send Message...".
See note further down

Finish
Here you have the possibility over the pre-selected option "Start Email program..." to start your email program with the created Hotinfo, the generated files as a file attachment and the correct destination address. You only need to press 'Send'.

Over option "Open Hotinfo file to save it..."you can open the support request, save, and send as an email attachment to support.de (please no spam) @ (please no spam) allplan.com, if no e-mail program is installed locally.
In this case, make sure to attach in addition to the support request all additional files also. Attach the "attached files" and "generated screenshots" independently as attachment to your email.

Download PDF  FAQ_EN_Generating_a_support_request_using_Hotinfo.pd...
Version:  Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016  | Last modified: 17.10.2018
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

Does Allplan create backup files (*.bak)?
How can I use these files?



Answer:

Allplan creates backup files when you do the following:

  1. Copy, Move Elements between Documents …
    Allplan creates a backup file of the destination drawing file or layout.
  2. Deleting drawing files and layoutsin the "Open on a project-specific basis" dialog box
    If you have selected "Create backup copies of drawing files", Allplan creates a backup file of the drawing file or layout.
  3. Importing data to drawing files
    If you have selected "Create backup copies of drawing files", Allplan creates a backup file of the drawing file.


Note on points 2 and 3:

To select the "Create backup copies of drawing files" option, click
Tools -> Options -> Desktop environment -> Save/load area (until V2009 Global Options -> Miscellaneous -> Autosave, Backup)->Create backup copies of drawing files.


Restoring:

If need be, you can restore the original drawing file or layout.
Make a note of the drawing file number or layout number and determine the corresponding project folder as follows:
Services application -> Service -> Hotline Tools -> wopro

Open this folder in Windows Explorer.

Rename the corresponding drawing file "tb000001.ndw" "tb000001.ndw.old" or the corresponding layout "pb000001.000" "pb000001.000.old.", for example.
Delete the bak extension from the corresponding bak file.

Example 1:

You have inadvertently copied the wrong elements to drawing file 4711.
1st step: exit the project in Allplan.
2nd step: delete file tb004711.ndw or rename it tb004711.ndw.old.
3rd step: find file tb004711.ndw.bak and rename it tb004711.ndw.

Example 2:

You have inadvertently copied the wrong elements to layout 815.
1st step: exit the project in Allplan.
2nd step: delete file pb000815.000 or rename it pb000815.000.old.
3rd step: find file pb000815.000.bak and rename it pb000815.000.



Note:

These backup files can considerably increase the volume of data to be backed up. So it is a good idea to delete the .bak files you no longer require before you start backing up data. To delete the .bak files, you can select the Services application and click Utilities -> Delete temporary files.

You can also find this information in the help for Allplan. Please refer to the topic "Using bak files".

Download PDF  FAQ_EN_Using_bak_files.pdf
Version:  Allplan  | Last modified: 26.11.2018
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I fix bugs in Microsoft .Net Framework components?



Answer:

Repairing .Net Framework up to and including version 4.6

Open the support site of the Microsoft company: https://support.microsoft.com/de-de/kb/2698555
Microsoft provides a repair tool for fixing .NET Framework up to and including version 4.6.

You can find this tool at https://www.microsoft.com/en-us/download/details.aspx?id=30135
Download the ‘NetFxRepairTool.exe’ file and save it to any folder on the hard disk of your computer.
Run the repair tool by right-clicking the ‘NetFxRepairTool.exe’ file and selecting ‘Run as administrator’ on the shortcut menu. This allows you to bypass Windows User Account Control.
Click ‘Yes’ at the following prompts.

Follow the instructions of the repair tool.

Repairing Net.Framework 4.7

Use the Net.Framework 4.7. Setup program to repair NetFramework 4.7.

You can download the Setup program for Net Framework 4.7 Setup from

https://support.microsoft.com/de-at/help/3186612/the-net-framework-4-7-developer-pack-and-language-packs

Go to the ‘Download information’ section and click ‘Download the Microsoft.NET Framework 4.7 Developer Pack now’.

You can see another dialog box in which you can select the installation package you want to download.

You can choose between NDP47-DevPack-KB3186612-ENU.exe (all language packages) and NDP47-DevPack-KB3186612-DEU.exe (German language package).

Select a package and download it. Then copy the Net Framework Setup program downloaded into a new folder you created on the hard disk (for example, C:\NetFrameworkSetup).

Start Windows Command Prompt.
Click in the Windows search box and type in ‘cmd’. The search result is ‘Command Prompt’.
Right-click ‘Command Prompt’ and select ‘Run as administrator’ on the shortcut menu.

Under Windows 8 and Windows 10, you can also start Command Prompt as the administrator by right-clicking the Microsoft logo on the Windows task bar.
You can then select ‘Command Prompt (Admin)’.

Depending on the Setup package downloaded
and the folder with the Setup package (for example, C:\NetFrameworkSetup),
enter the following command: C:\NetFrameworkSetup\NDP47-DevPack-KB3186612-DEU.exe /repair /norestart or
C:\NetFrameworkSetup\NDP47-DevPack-KB3186612-ENU.exe /repair /norestart.

You can see a dialog box with the installation options of Microsoft .Net Framework Setup. Click the ‘Repair’ button.

This repairs the Net Framework 4.7 components.

You can define some optional parameters when installing or repairing .NET Framework 4.7:







If this does not repair Microsoft.NetFramework on your computer, you can try the .Net Framework cleanup tool on Microsoft’s support site.

You can download the .Net Framework cleanup tool from
https://blogs.msdn.microsoft.com/astebner/2008/08/28/net-framework-cleanup-tool-users-guide/

After running the .Net Framework cleanup tool, you must re-install the .Net Framework components removed by the cleanup tool.


Download PDF  FAQ_EN_Repairing_Microsoft_Net_Framework_46_and_Net_...
Version:  Allplan 2015 / Allplan 2014 / Allplan 2013  | Last modified: 25.06.2019
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

What can I do if Allplan starts as a viewer only and I have to install a new hardlock driver?



Answer:

Install the latest hardlock driver.

How to install:

Use the following link to download the driver:

https://webdrive.allplan.com/s/4LrjrymoxESzC6p

The driver for Windows 7 and 8.1 is in the following folder.
/Download/Allgemein/Dongle/

If you are using Windows 10 then use the driver under the folder:
/Download/Allgemein/Dongle/Win10

Extract and save the 'haspdinst.exe' file to any folder, for example, c:\drivers. Then open the command prompt:
Right-click Start (Windows button) -> Command Prompt (Admin)
Switch to the folder where you saved the file. To do this, type in "cd c:\drivers".

To remove the old drivers, enter the following command:
haspdinst -fremove
Next, install the new driver:
haspdinst -install


Note:

If you use a parallel hardlock, read the following instructions:
https://connect.allplan.com/en/faqid/20121011092418.html

Download PDF  FAQ_EN_Installing_a_new_hardlock_driver.pdf
Version:  Allplan 2019 / Allplan 2018  | Last modified: 17.06.2019
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I set up Allplan Share? What are the requirements?


Answer:

1)System requirementsfor Allplan Share

Software required

Allplan Version 2018 or higher

Network infrastructure required

Minimum requirements:

A 20-Mbit/s Internet connection for downloading and uploading data

Recommended setup:

At least a 50-Mbit/s Internet connection for downloading and uploading data

2) Licensing

You have two options to buy the Allplan Share option.

1. You can visit the Allplan Shop at ‘shop.allplan.com’.

Allplan Options -> Allplan Share

a. Specify how many licenses you want to buy and add the Allplan Share option to the cart.

b. Follow the instructions displayed and buy the Allplan Share option.

After you have bought the Allplan Share option, the licenses will be assigned to your Bimplus team. You can manage these licenses using ‘My Account’ - ‘Subscriptions and Users’.

2. You can contact the Allplan sales partner in your area.

3) Assigning licenses

Regardless of how you buy the Allplan Share option, you can manage the Allplan Share licenses in the Allplan Shop. Go to the ‘Subscriptions and Users’ area. As an alternative, you can also manage the licenses on the Bimplus portal. Here, go to the ‘Team members’ area.

Allplan Shop - ‘Subscriptions and Users’

1. Log in to the Allplan Shop and open ‘My Account’.

2. Click ‘Subscriptions and Users’ to see your licenses.

3. Select the Allplan Share option on the tab.

4. You can assign one or more Allplan Share licenses to team members. To do this, select the user in the list and assign the license by selecting the check box. You can remove the license at any time by clearing the check box.

If the list does not include the user to whom you want to assign a license, click ‘Invite new Bimplus team member’, enter the email address of the new team member and select a role.

As soon as the new team member has accepted the invitation, you can find this person in the list.

4) Using Allplan Share

To use the Allplan Share option, you require Allplan 2018. The Workgroup Manager option is not necessary.

Starting a project

You have three options to start an Allplan Share project:

1. You can create a new project and save it on Bimplus by setting the location to BIMPLUS. To create a Bimplus project with Allplan Share content, you require ‘Bimplus team owner’ or ‘Bimplus team admin’ privileges.

2. You can copy an existing Allplan project to Bimplus by selecting ‘Copy to’. You can then share this project with other project partners. This does not affect the source project.

3. You can move an existing Allplan project to Bimplus by selecting ‘Move to’. This moves the source project to Bimplus. As a result, this project is no longer available on the local computer or local network.

5) Managing users and assigning users to the project

Allplan Share is a cloud-based solution. Therefore, Allplan Share uses the Bimplus user management for project collaboration. As a result, Allplan Share is independent of local user management systems like Workgroup Manager.

After you have copied or moved an existing Allplan project to Bimplus, you must reassign the users to this project. Otherwise, they cannot access this project.

To define the project members, use the Bimplus project administration. In addition, you must invite new project members to the Bimplus project.

If these Bimplus project members are to use the Allplan Share option too, you must assign an Allplan Share license to each member in advance (as described in ‘3) Assigning licenses’).


Download PDF  FAQ_EN_Allplan_Share.pdf
Version:  Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017  | Last modified: 28.10.2019
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

Can I "automate" the installation of Allplan?


Answer:

You can install Allplan 2017 in silent mode. This installation mode is fully automatic; you do not need to enter anything. Silent installation is particularly useful if you want to install Allplan 2017 with the same settings on a large number of workstations on a network.

Requirements for installing in silent mode:

Pay attention to the different licensing types!

Licensing for stand-alone workstations:
Make sure you have not yet activated a license on the computer where you want to record silent installation. Use the Viewer option for recording.

After having installed all computers in silent mode, you must use the Product Key to activate the license locally on each computer.
To activate the license after installation:

  • Open the 'License settings' dialog box: Services application -> Utilities -> License settings
  • Click License activationon the left.
  • Enter your Product Key.
  • Click Activate license.


Using a license server:

  • The clients take the licenses from a license server.
  • The license server is installed.
  • The license of the license server is activated.

For more information on the license server, go to https://connect.allplan.com/en/faqid/20150618084450.html
Use the Use active licenseoption for recording.

Setup writes the license settings to the %AppData%\Nemetschek\Lic3.ini file.You must distribute this file to all computers.


Some more tips:

  • Before you start installing, unzip the Allplan installation package (for example, using the 7_Zip program). Make sure this package is in a folder that can be accessed by all clients you want to install.
  • Start the command prompt for running the setup program always as a local administrator. To do this, open the shortcut menu and select "Run as administrator". Make sure you always start the command prompt from the correct folder.
  • Setup will automatically install any Microsoft components required by Allplan such as Microsoft .NET-Framework or Microsoft Report Viewer without prompting you to confirm.




Preparing to install in silent mode

To record and run silent installation, you need the installation files of Allplan 2017.
Installing in silent mode involves three steps:

Creating the log file for installing in silent mode

Start by installing Allplan 2017 with the /r option on a typical workstation. During installation, Setup automatically writes all entries to a log file named setup.iss. You can then use this file to install the program on the other workstations.

Installing in silent mode

Next, install Allplan 2017 with the /s option on all other workstations. Installation is based on the setup.iss log file you created in the first step.

Checking the installation

Finally, you should check the setup.log file, which was created automatically during setup, to see whether everything was installed correctly.

Note: When installing in silent mode, Setup usually uses the same setup.iss file to install the program on all workstations. However, you can edit some settings of the setup.iss file if you want to adjust paths. You can find more information in the help; see Adjusting the setup.iss filehttp://help.allplan.com/Allplan/2017-0/1031/Allplan/index.htm#331.htm


To install Allplan in silent mode, do the following:

Install .NET 4.6
Silent setup requires you to install .NET 4.6 in advance. The reason for this is that you have to reboot the computer after installation of .NET 4.6. This reboot would interrupt silent installation.


After you have downloaded the installation files, you must unzip these files before you can use them to install in silent mode.

  • Unzip the zip file downloaded. This results in an .exe file (for example, Allplan 2017-0-5-cad.exe).
  • Then unzip this .exe file using an appropriate program (for example, 7_Zip) and save the resulting file to any folder. You can now use the command prompt to start Setup.exe for recording.



1. Sample installation:
Start by creating a record file. To do this, run setup with the settings you need. You only need to do this once.

Use the command prompt to start this installation with the "/r" option (for record):

To run the setup program, open the command prompt as a local administrator and type the following:
setup.exe /r

Setup starts and runs as usual.

Stand-alone license:
When you are prompted to choose the license configuration, select the Use vieweroption.
License server:
When you are prompted to choose the license configuration, select the Use active licenseoption.


Setup logs the entire installation process, writing everything to the setup.iss file.

If you want, you can change the name and folder of this file:

setup.exe /r /f1<folder>:\Setup.iss
For example,
setup.exe /r /f1c:\Setup.iss
This saves the file directly to C:\.

Be careful:
There must not be any blanks between "f1" and the folder!

Copy the setup.iss file to a folder that can be accessed by all clients you want to install. It is a good idea to copy this file to the folder with the Allplan installation files.

License server:
Copy the %AppData%\Nemetschek\Lic3.inifile to the %AppData%\Nemetschek folder of every client.
If you install Allplan on a client for the first time, you must create the Nemetschek folder in %AppData% first (for example, C:\Users\Username\Appdata\Roaming\Nemetschek).


2. Silent installation:
Make sure you can access the setup.iss file.

License server:
Make sure the Lic3.ini file is in the %AppData%\Nemetschek\ folder.


Setup logs the entire installation process again, writing everything to the setup.log file. You can find this file in the same folder as the setup.iss file. With the /f2 option, you can specify a different folder and file name for the setup.log file.

To start installing Allplan in silent mode on a client, open command prompt as a local administrator and type the following:

setup.exe /s /f1<folder>:\Setup.iss /f2<folder>:\Setup.log

For example,
setup.exe /s /f1c:\Setup.iss /f2c:\Setup.log
This saves the file directly to C:\.

Check the setup.log file to see whether everything has been installed correctly. The [ResponseResult] section should return the 'ResultCode=0' value.



Note:

If you have several licenses or license servers, select the required license for each client using the Services application - Utilities - License settings.

Refer to the online help for detailed information on installing in silent mode.
http://help.allplan.com/Allplan/2017-0/1031/Allplan/index.htm#321.htm
To open the help system, press the F1 key during setup. Go to the "Contents" tab, select "Installing" and then "Installing in silent mode".

You can also find information in the help for the license settings:
Services application -> Utilities -> License settings
To open the help system, press the F1 key. Go to the "Contents" tab, select "Licensing Allplan using a license server" and then "Installing in silent mode".


Please note that we cannot provide support for this installation method.

Download PDF  FAQ_EN_Allplan_silent_installation_(Allplan_2017_and...
1 - 10 (23)
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
https://campus.allplan.com/ uses cookies  -  More information

Accept