Результат поиска

1 - 9 (9)
  • 1
Версия:  Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016 / Allplan 2015 / Allplan 2014 / Allplan 2013 / Allplan 2012 / Allplan 2011  | Последнее изменение: 17.10.2019
5 user(s) found this FAQ helpful

Allplan from version 2011

Parts of Allplan 2011 have been reprogrammed and are completely new. Allplan uses a graphics library, which has been developed especially for CAD programs and visualization tasks. Depending on the data type and application, the display speed of Allplan is much higher than that of earlier versions, and refresh operations are considerably shorter. What's more, you can create hidden line images in real time.
This new technology is not a one-to-one implementation of the software-based solution in the previous version. Instead, a hardware-based approach is used. When it comes to data processing, the graphics card takes on much of the work. The different behavior of these two technologies that may occur in some parts is inherent. Therefore, the resulting display and refresh operations may differ slightly from what you are used to.



General graphics card requirements for Allplan

To fully exploit hardware acceleration capabilities, you require an Open GL 2.0 and DirectX10 (chip-based) compatible graphics card with 512 MB or more memory. Although Windows XP does not support DirectX10, Allplan only requires the chip-based support of the graphics card to manage the graphics library. OpenGL 2.0 is used in 2D and in visualization windows. These changes employ the latest technology in graphic display, so selecting a capable graphics card, and using the proper drivers is essential.

For more information on graphics card specifications, go to:

http://en.wikipedia.org/wiki/Comparison_of_AMD_graphics_processing_units
http://en.wikipedia.org/wiki/Comparison_of_NVIDIA_graphics_processing_units#Quadro)



Professional graphics cards versus Consumer-Level cards

Graphic card manufacturers typically have different product lines targeted for "gamers" and "professional users". While the hardware setup is very similar in case of both cards, there are key differences in their firmware and driver. "Consumer-Level cards" (such as Nvidia GeForce and AMD/ATI Radeon) are optimized for 3D games and technologically designed for DirectX10, as speed is more important than image quality.
Typically a 3D model in a game contains a low number of polygons with textures applied to them, while in CAD applications polygon count is high, and the image quality of wireframe models or shaded models is more important than navigation speed. Also, professional cards' memory usage is optimized for using multiple application windows, while in gaming this is not relevant.
Another key difference between the two product lines is the way they are delivered and supported. Professional cards (such as Nvidia Quadro and AMD/ATI FireGL/PRO) are built according to the video chip manufacturer's references, so you can always be sure that the driver delivered by the video chip manufacturer (such as Nvidia or AMD/ATI) fits your card.
The manufacturers of Consumer-Level cards (such as ASUS, Sapphire, Gigabyte, PNY and so on) may diverge from the chip manufacturer's references, so their drivers may not be compatible with the chip manufacturer's reference driver. Also, the product life cycle and driver release cycles are much shorter in case of gaming cards, usually 6 months up to 1 year at most and a 1-year warranty period maximum.

Example: comparison of graphics cards

Consumer-Level cards
Professional graphics cards / workstation
Products
Radeon
FireMV
FireGL/Pro
Mobility FireGL/Pro
Markets
  • Private customers: desktop systems and notebook systems
  • Corporate desktop systems
  • Corporate CAD and DCC desktop systems and notebook systems
Applications
  • Home/office publishing, productivity, multimedia, games, Internet
  • Finance, clearance, logistics, airport information displays
  • CAD/CAM/CAE, AEC, DCC, GIS, MI, visual simulation, scientific research/imaging
Certification
  • WHQL certification
  • Industrial applications
  • WHQL certification
  • Professional 3D applications
  • WHQL certification
Operating
systems
  • Windows 98SE / Me / XP
  • Windows Vista,
    Windows 7
  • Windows XP, XP64,Vista, Vista 64, Windows 7, Windows 7 64
  • Linux
Drivers
  • Optimized for DirectX
  • Basic Open GL
  • Optimized and designed for DirectX
  • Optimized and advanced Open GL
Life cycle
  • Available for 1 year on average
  • Available for 2-3 years on average
Support
  • Basic, private customers
  • Direct access to dedicated support by trained technicians
Warranty
  • 1 year
  • 3 years with replacementof components




Professional graphics cards versus Consumer-Level cards

Professional graphics cards differ considerably from "Consumer-Level cards" for private users with regard to specific market segments with special requirements:

  • Extensive application tests and certifications with CAD providers
  • Optimized and advanced support for API as well as further developments
  • Longer product life cycles and availability
  • Direct product support
  • Longer warranty period


Nemetschek Allplan GmbH cooperates with Nvidia und AMD to test graphics card drivers for the Nvidia FX Quadro/ Quadro and AMD/ATI FireGL/ Fire Pro series. These product lines are tested, certified and recommended for Allplan by Nemetschek Allplan Systems GmbH.

For more information on certified graphics cards, go to:

www.nemetschek.eu/info/grafikkarten
www.nemetschek.eu/info/graphiccards

There are four different categories and areas:

Graphics cardApplicationQuality testsStatus
Gaming graphics cards3D GamesTested / not testedNot recommended
    
Professional graphics cards3D basisCertified and recommendedEnd of life
    
Professional graphics cards3D performanceCertified and recommendedEnd of life
    
Professional graphics cards3D high performanceCertified and recommendedEnd of life




Recommended graphics cards for laptops (Windows)

For reasons detailed above, we cannot recommend any specific card and driver combination for laptops. However, there are professional graphics cards available for high-end laptops such as NVidia FX Quadro & Quadro NVidia "M" or AMD/ATI FireGL & FirePro "Mobility".
These graphics cards are just as good as their desktop counterparts.
Laptops with Consumer-Level cards have been tested only briefly and cannot be recommended. We have had bad experience with on-board Intel graphics cards.



Graphics cards drivers for Apple Macintosh

Since Macs come with a default graphics card (on-board or gaming), and the drivers are bundled with system updates, we cannot recommend a specific card.
Graphics cards for MacOsX 10.6 (Leopard) or later and Boot Camp support Open GL 2.0 and DirectX10. Currently, there is only one series that is equipped with a professional graphics card: Mac Pro with NVidia FX4800 for Mac.


Notes for Allplan and Macintosh:

  • There is no provision for a direct installation under Macintosh.
  • Access to Windows must be straight from the Boot Camp installation.
  • For performance reasons, Parallels Desktop cannot be used in conjunction with Nemetschek Allplan.


We kindly ask you to understand that Nemetschek Allplan cannot provide support for Boot Camp installations.



Installing graphics cards drivers (Windows)

Graphics cards only work properly if they have a hardware provider supplied driver (not system built-in driver) installed correctly. It may happen that remnants of a previous installation interfere with the current driver installation. If you experience display issues with the drivers listed below, please "clean-install" the driver again. "Clean-install" means removing all previous driver files before installing a new driver. Unfortunately, a simple uninstall may not efficiently remove all components of a driver. There are tools that can do it, like ATI's cat uninstaller or third-party tools like driver cleaner or driver cleaner pro 1.5.



Graphics card drivers for laptops (Windows)

In most cases, graphic card drivers for laptops are supplied by the laptop manufacturer, and graphic card provider supplied drivers will not install on laptops. This makes it practically impossible for us to test laptop graphics cards. If you are experiencing display issues with your laptop, and your supplier does not offer you a driver update, you might try - at your own risk - to tweak a desktop driver to work on your laptop. Note that this is obviously not encouraged by your laptop supplier.

Загрузка PDF  FAQ_EN_Graphics_cards_for_Allplan.pdf
Версия:  Allplan 2021 / Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017  | Последнее изменение: 01.10.2020
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I temporarily borrow a license for a client from the license server?



Answer:

To borrow a license, do the following:

Notes:
You cannot borrow licenses on the license server. You can do this only at the clients.
You can only borrow and return a license if the client is connected with the license server.
Computers that are not on the company network must use a VPN connection to access the server.

At the client:

  • Open the 'License settings' dialog box: Services application -> Utilities -> License settings.
  • Click License selectionon the left. Then click the license you want to borrow so that this license is highlighted in blue.
  • If this license is a license server license, the Todayand Borrowbuttons in the 'Borrow license for:' area are no longer grayed out.
  • The Todaybutton always shows the preset period of time. The default setting is Today. If you want to change the period of time, click the Todaybutton. You can then choose from various options.
    Note: When you select 'Today', the license will be available again for all Allplan users on the server tomorrow.
    When you select a number of days, borrowing will always be valid for 24 hours. For example, you borrow a license for 1 day and borrowing starts at 3 o'clock in the afternoon, the license will not be available on the server until 3 o'clock in the afternoon. The same applies to selecting days on the calendar.
  • After having specified the correct period, click Borrowto borrow the license at once.


You can immediately see the borrowed license in the license selection below your computer name. Click the green information button to get details about this license. For example, you can see when the borrowed license will automatically be returned to the server.

  • If you want to return the license to the server before the time period expires, click the license again so that it is highlighted in blue. The Return licensebutton is now available. Click Return licenseto immediately return the selected license to the server.


Загрузка PDF  FAQ_EN_License_server_-_borrowing_licenses_temporari...
Версия:  Allplan 2020 / Allplan 2019 / Allplan 2018  | Последнее изменение: 12.11.2020
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I change the cache path for Allplan Share?

Note:

You do this at your own risk.
We strongly recommend that you clarify all issues in advance.
Always copy a file before you change it.
Before you change registry entries, back up the registry key that you want to modify. To do this, export the key by selecting File - Export in the Registry Editor.

Answer:

Allplan Share temporarily saves the project data in the path of the local file storage, which you defined when you installed Allplan.
You can see the path of the local file storage folder in the Services application.
If this folder is centrally on a server for all Allplan workstations:
To avoid replication conflicts that might occur when several users work on the same project data, you must change the path settings for each user so that this folder is locally on the user’s computer running Allplan.

Before you start, close Allplan, making sure that you do not lose any data.

  1. Go to a local drive (C or D) of the computer running Allplan and create the new "Local data” folder with the "Allplan” subfolder (for example, C:\Local data\Allplan).
  2. Start the Windows Registry Editor as the administrator (start - run - regedit).
  3. Go to the left column of Registry Editor and open the following key: HKEY_LOCAL_MACHINE\SOFTWARE\Nemetschek\Allplan\2018.0\InstallRoot. If Allplan 2019 or a newer Allplan version is installed, “2019.0“ or the newer version replaces “2018.0” in the path.
  4. Go to the right column of Registry Editor and double-click theLocalDataDrivekey. Specify the drive that you selected for local file storage (for example, C:). Then click OK to confirm the change. This applies the change.
  5. Then, go to the right column of Registry Editor again and double-click theLocalDataPathkey. Specify the path that you defined for local file storage (for example,\Local Data\Allplan). Then click OK to confirm the change. This applies the change. The result should look like this:
  6. Close the Registry Editor. Allplan now uses the new path for the cache of Allplan Share.
  7. Start Allplan and select the Allplan Share project to load the necessary project data into the new cache.



Загрузка PDF  FAQ_EN_Adjusting_the_local_file_storage_folder_for_A...
Версия:  Allplan 2021 / Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016  | Последнее изменение: 30.09.2020
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I make several projects available to users when Workgroup Manager is installed?



Answer:

You can make several projects available to a user or define a user as the project owner of several projects.

Do the following:

First, log in as the Allplan administrator.
If necessary, set up an Allplan user for the new Windows user: Services application -> Workgroup Manager -> Configuration -> Add a user
(Allplan 2014 and later:Services application -> Workgroup Manager ->Administer users)

Start Allplan and then ProjectPilot by clicking
File -> ProjectPilot

Open the Projects folder in the area on the left.
You can see all the projects in the Contents of "Projects" area on the right.

a. Making several projects available to users:
In the area on the right, select the projects to which you want to add users or from which you want to remove users (CTRL or SHIFT key or use a selection rectangle).

Click one of the selected projects with the mouse button. On the shortcut menu, click
Add / remove authorized users...
The Add / Remove Authorized Usersdialog box opens.

Select the users you want to add to or remove from the selected projects.
Note:
The user list displayed only helps you select users. It does not list all the authorized users currently assigned to projects.

Click Addor Remove.
This adds or removes the selected users to or from the selected projects. Whether users you have already added to a project are added again is irrelevant. The same applies if you remove users you have never added to a project.

b. Defining a project owner for several projects
In the area on the right, select the projects for which you want to define the owner (CTRL or SHIFT key).

Click one of the selected projects with the mouse button. On the shortcut menu, click
Change project owner...
The Define Owner dialog box opens.

Select the user you want to define as the owner of the selected projects.
Note: The user list displayed helps you select users. You can define only one user as the owner.

Click OK.

c. Defining a project owner for a project or making a project available to several users(also applies to earlier versions):
In ProjectPilot in the area on the right, click the relevant project with the right mouse button. On the shortcut menu, click Properties.
The Properties for <project name>dialog box opens. Switch to the Security tab and define the owner and the authorized users.



Note:

You can add or remove project users or define the project owner only if the projects in question are in the current Allplan format.

Загрузка PDF  FAQ_EN_Making_several_projects_available_to_users.pd...
Версия:  Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016 / Allplan 2015 / Allplan 2014  | Последнее изменение: 20.08.2019
Not voted yet. Be the first to vote this FAQ as helpful!

Questions:

Why can’t I see anything in a project or why are elements missing from drawing files?
Why are layers not visible?
Why is it not possible to select a privilege set in layer selection?



Answer:

Probably, you have not yet been assigned any privilege sets or the layers are frozen in the privilege set in question. First, check whether you can select another privilege set.


1. Selecting another privilege set

To do this, select the project in question and open the layer settings(Format -> Select, Set Layers). Go to the “Privilege set in list box” area at the top on the right and check whether you can select another privilege set (for example, ALLPLAN).
By default, all layers have full access rights in the predefined ALLPLAN privilege set.

If there is no privilege set with full access rights, you should assign the privilege sets correctly.
This can only be done by a user with administrator privilegesor, in the case of a project-specific layer structure, by the project owner.

Thus, log on as a user with administrator privileges and do the following:


2. Assigning a privilege set

Select the project with the frozen layers.

Open the layer settings(Format -> Select, Set Layers). Switch to the "Privilege Set" tab and click Define, modify privilege set.

Select the relevant user and assign the privilege set using the arrows.

Click OKto confirm.


3. Adjusting layers’ access rights in the privilege set

Finally, check the access rights of the layers in the privilege set assigned.
Go to the "Privilege set in list box" area at the top on the right and select the relevant privilege set (for example, ALLPLAN).

Check the area on the left to see whether there are frozen layers (gray or white). To change this, select these layers or simply select all layers using CTRL+A. Then click the Full access right (modifiable)icon in the “Change rights” area.
Click OKto confirm.

The next time you open this project, you can select this privilege set in the layer settings. You can then see all layers and set them to modifiable.

Do the same with print sets.


Alternative:

Since version 2006, the administrator has been able to select Show all users all print sets and privilege setsin the “Administrator options” group on the “Privilege Set” tab (“Design group” in version 2006). Thus, you do not need to assign new users to privilege sets. This option applies to all projects.

However, as soon as a user has been given a privilege set or print set, this option no longer applies to this user.



Note:

As a project can have its own layer structure, it is essential that you check the privilege set in the correct project.
To find out whether a project has its own layer structure, click
File -> New Project, Open Project-> right-click the relevant project -> Properties. Check whether the path settings for Layerstructuresare set to Officeor Project.

Загрузка PDF  FAQ_EN_Enabling_privilege_set_for_user.pdf
Версия:  Allplan 2021 / Allplan 2020 / Allplan 2019  | Последнее изменение: 05.11.2020
Not voted yet. Be the first to vote this FAQ as helpful!

Question:
How can I work together on a project with a partner from another country?

Answer:
Using Allplan 2019 and later, you can work on projects across countries.
You can define projects in a country-specific manner. This means that a project gets the resources (for example, hatching, patterns, layers and so on) and reinforcement settings of a specific country. Depending on your license, you can install one or more additional country packages. For example, you can then create a project with resources and settings for Germany and another one with resources and settings for the UK.


Requirements:

Whether you can use country packages depends on the Allplan license.

Only the ‘Cubed’ and ‘Exponential’ license types include country packages.
These license types enable you to use as many country packages as you like. You can create and open projects with any country code.

The ‘Lineared’ and ‘Squared’ license types only include one country package by default. This also applies to all conventional license types such as ‘Architecture’ and ‘Engineering’. In other words, you can only create and open projects with this country code.

Installing country packages:

When installing Allplan 2019 for the first time or upgrading from Allplan 2018 or earlier, you must explicitly install the additional country packages.

A default installation onlyinstalls the country package of your country. If you want to use different country packages, you must do a custom installation. Only a custom installation allows you to select the country packages you want to install.
You can do this whenever you want - be it the first installation or an upgrade or update.

Doing a custom installation:
Start Setup.

Select Customfor the Setup type.
When it comes to selecting Features, you can select the language packages you want to install.
You can see a list of all Allplan languages included in your license.
After this, you can select the countries. Select the country packages you want to install.
Click ‘Next’ to confirm all other dialog boxes.

Note:Please note that the more country packages you select, the longer the installation will take and the more hard disk space will be required.

Using country packages in Allplan:

You must define the country when you create a project. You cannot change the country later.

Creating a new project:
When creating a new project, you can select the county in country-specific templates.
Select the country and the template you need.

If you do not select a project template, you must select the required country in the next dialog box.


In the project:
The status bar shows the country set for a project.
The units for length entries and reinforcement set in the Options are project-specific settings. These units are preset depending on the country selected.



Important note:
  • When checking out a project in a workgroup environment, you can choose which country-specific office standard you want to check out.
  • Click in the ‘License Settings’ to see which countries are included in your license.
  • There is a default country, which is usually the country entered in your license. Setup always installs the data for this default country in the STD and ETC folders. During installation, Setup creates a STD.??? folder and an ETC.??? folder for each additionalcountry package selected (??? stands for the country code). The office path and default path are always based on the country set for the project that is currently open. That is to say, when you open a project and save a favorite or library element in the office path or default path, these elements will only be available in projects with the same country settings. ProjectPilot is an exception; here, the office path and default path always refer to the STD and ETC folders.


Загрузка PDF  FAQ_EN_Country-specific_projects_-_working_together_...
Версия:  Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017  | Последнее изменение: 24.10.2019
1 user(s) found this FAQ helpful

Question:

How can I give individual users the right to see and select specific seats on the license server? And how can I deny users this right?
Sometimes, it may be necessary that a specific user does not see the seat with, for example, the terrain option so that this user cannot use this seat inadvertently.


Answer:

Using WebAdmin, you can give users rights for specific seats on the license server.
Please note the following points:

1. Before you start, check that at least CodeMeter Version 6.50 is installed on the license server.
Start CodeMeter Control Centeron the server.
To do this, use the Windows start menu and select CodeMeter -> CodeMeter Control Center. As an alternative, open Search by clicking the Search button on the Start screen. Enter Codemeter and press ENTER. Select Help -> About to see which version of CodeMeter is installed. If the version displayed is older than version 6.50, you must install the latest version of CodeMeter Control Center. Go to the following website
and download the CodeMeter User Runtime for Windowsprogram.

https://www.wibu.com/de/anwendersoftware.html

2. Open WebAdmin. Start CodeMeter Control Centeron the server again.
To do this, use the Windows start menu and select CodeMeter -> CodeMeter Control Center. As an alternative, open Search by clicking the Search button on the Start screen, enter Codemeter and press ENTER. A dialog box opens. Click WebAdminat bottom right.

Or
Enter Localhost:22350in the address bar of your browser.

3. Go to "Configuration -> Server -> License Access Permissions".
Select Mode: Advanced.

4. Go to "Advanced Mode Configuration -> Specific access rules -> Add Firm Code"and select "6000100 - Allplan GmbH". Click Add. "Specific access rules"now inlcude "6000100 - Allplan GmbH".





5. Click "Add Product Code"to select the seat for which you want to define access rights. However, this is only possible if the "Distinction based on Product Item Text" check box is selected.
The "Note" section below in this FAQ lists the abbreviations given at the end of each seat. These abbreviations represent the license contents.
Select the required seat and click "Add" again. Repeat these steps to assign more seats.





6. After having defined the product code, you can now assign an access rule.
By default, all users are allowedto access this seat.
Select the product code you just defined and click "Add new access rule".
Click "User" and enter the required user.
When you click in the field next to "User", you can see all available users with their domain names.
Select the user or enter the user manually. For example, enter DOMAINNAME\SSample and select the right you want to assign to this user by clicking "Allow" or "Deny".

If the default setting is "Allow", you can thus deny users access to the license. If the default setting is "Deny", you can thus allow users to access the license again.
You can add more rules. When you have configured all rules, click "Apply" to apply the changes.

7. You need to restart CodeMeter Service so that the changes take effect.
To do this, select CodeMeter Control Center -> Process -> Stop CodeMeterServiceand then click Restart CodeMeter Service.Before you restart the service, make sure all users have closed Allplan.


Information:

Client access can be defined by one of the following parameters: computer name, IPv4 subnet, user name or group name.
Enter the required parameter in the corresponding field. If you use an active directory, the program auto-completes entries in the "User" and "Group" fields.


Here comes a practical example:

Think about which setting is most useful to you. For example, you have two seats: seat 01 with 7 architecture licenses and seat 02 with 1 architecture license and 1 terrain license. Only two specific users should be able to use seat 02. If you want to deny all other users access to seat 02, you need to add seat 02 to specific access rules and define a rule for this seat 02. First, set the default setting to "Deny". Then, add these two users and select or "Allow" for these users. As a result, all other users can only see seat 01 and these two users can see seats 01 and 02.

However, if you want that these two users can only see seat 02, you need to add both seats to specific access rules and define a second rule for seat 01. Add these two users to this second role and select Deny for these two users. The default setting, which applies to all the other users, is still Allow. As a result, all other users can see seat 01 and these two users can only see seat 02.


Note:

The following abbreviations are used:

T Terrain
B Bamtec
W Workgroup
K Key Plan
M Bridge Modeler
L Cadastral plans for conduits
S Language option
V Visualization
A Architecture option
E Engineering option

Here are some examples:

Architecture:
"Allplan Architecture 2017”

Architecture + Terrain
"Allplan Architecture 2017 T"

Architecture + Bridge Modeler
"Allplan Architecture 2017 M"

Architecture + Terrain + Bridge Modeler
"Allplan Architecture 2017 TM"

Загрузка PDF  FAQ_EN_License_server_-_assigning_access_rights_for_...
Версия:  Allplan 2020 / Allplan 2019  | Последнее изменение: 08.04.2020
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

You may ask yourself on which occasions or user actions Allplan synchronizes drawing files and plans with the Bimplus Cloud in an Allplan Share project.


Answer:

The following cases apply to drawing files:


Case 1:
Drawing files in a share project are uploaded to the Bimplus cloud for synchronization if all three of the following conditions apply:

  • A change has occurred on the drawing files
  • The drawing files have been changed to gray or deselected
  • Open on a project-specific basis is closed


If other users have the drawing file which meets all the criteria in case one, grayed out (i.e. it is passively in the background), then after the first user has carried out all three steps, they will automatically receive a message informing them that there have been changes to the drawing file. They can then either display or reject these changes.
If the other users do not see this message, they should make sure that they are using the latest version of their Allplan installation and that the check mark is set in the options for
Options -> Desktop Environment -> Save/Load -> For changes in reference drawing files show message. If the check mark is not set, simply set it and restart Allplan.

Case two:
In Allplan, click on Allplan A in the top left-hand corner and select Save all -> all drawing files that have changes are synchronized.

In this case too, as in case 1, a message is sent to all users who have the drawing file, to which all the criteria from case 1 apply, in grey (i.e. passively in the background).

Case three:
Even if you simply open the function New project, Open Project, all drawing files that have been modified are synchronized

Case four:
When you call up the Layout Editor, all drawing files that have been changed are also synchronized



The following applies to plans:
If drawing file contents in the plan change, then the plan is NOT uploaded - no need . Plans are only uploaded if either something changes in the plan layout (move or delete a plan element in the plan, etc.) or, for example, the scale or drawing type of a plan element is changed. The upload then takes place automatically when you change the plan or leave the plan layout.




Note:

In Allplan version 2018, these notes also apply accordingly; only case 2 for drawing files does not work in this version.

Загрузка PDF  FAQ_EN_When_do_Allplan_share_projects_synchronize_dr...
Версия:  Allplan 2020 / Allplan 2019 / Allplan 2018  | Последнее изменение: 24.10.2019
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I switch Allplan from German to English?



Answer:

Allplan 2018 is the first version to include English in the license by default.
This means that by installing Allplan 2018, you automatically install the English version too.
As a result, you can switch languages using the Services application.

Important! This switch only applies to the program itself.
The content of the defaults (standards and country-specific content) does not change and is still in German.

Before starting Allplan, you can select the language using the Services application.
To do this, select Configuration -> Language. ‘Current setting’ shows the language currently selected.
Select the required language in the area at the bottom, that is, English.
A German default license only includes German and English.





Allplan now starts in English.



Note:

If English is not included in the Services application, you can install this language (or other languages you purchased) at any time.

All you need to do is download the current installation package of the version you use. You can find this package at www.connect.allplan.com

During installation, select Update installationand Use active license.

Select Customfor the Setup type.

When it comes to selecting Features, select the required language(s) in the ‘Language packages’ area.
This area lists the languages included in your license.
Do not change the other settings and click ‘Next’ to confirm the following dialog boxes.




After installation, start the Services application-> Configuration -> Language. Select the required language.

Загрузка PDF  FAQ_EN_Using_Allplan_in_English.pdf
1 - 9 (9)
  • 1
https://campus.allplan.com/ uses cookies  -  More information

Accept