Результат поиска

1 - 8 (8)
  • 1
Версия:  Allplan 2018 / Allplan 2017 / Allplan 2016 / Allplan 2015 / Allplan 2014 / Allplan 2013 / Allplan 2012 / Allplan 2011  | Последнее изменение: 15.11.2017
1 user(s) found this FAQ helpful

Question:

How can I update cross-section catalogs or install country-specific cross-section catalogs in Allplan 2011 and later?



Answer:

To install and save cross-section catalogs in Allplan 2011 and later, select Tools -> Defaults -> Cross-Section Catalogs. A dialog box opens. You can find a folder symbol and a disk symbol at bottom left.

To install cross-section catalogs, use the folder symbol. Another dialog opens, where you can select the cross-section catalog file you want to install. Select the file to be installed and click "Open" to confirm. This installs the corresponding cross-section catalog, which you can now use in Allplan.
To install country-specific cross-section catalogs, select the "Ing" folder, which was created when you installed Allplan. You can find it in the Allplan installation path (e.g., c:\Nemetschek\Allplan 201x\New\Ing - more information on the Allplan installation path is provided below in the "Notes" section).
This folder includes the country-specify cross-section catalog files.

To save a custom cross-section catalog, use the disk symbol. Another dialog opens, where you can select any folder to save the cross-section catalogs currently used in Allplan.



Note:

To update cross-section catalogs, you may need administrator privileges. If necessary, log on as an administrator before you start the update.

To use the cross-section catalogs for a specific project only, set the path settings for the cross-section catalogs of this project to project before you install the cross-section catalogs. In Allplan, open the "File" menu and select "Open Project..." Click the corresponding project with the right mouse button. Select "Properties". A dialog box opens. In the "Path settings" area, set the "Bar and mesh cross-section catalogs" to "Project".

To determine the path where Allplan is installed, use the Services application and select Service -> Hotline Tools-> showcfg. The Services application window shows the path of the Allplan installation folder.

The following abbreviations are used for the country-specific cross-section catalogs in the file names (axyzqusr.txt):
aut Austria
bel Belgium
bra Brazil
bul Bulgaria
deu Germany
eng England
fra France
hol Holland
hrv Croatia
ita Italy
kor Korea
pol Poland
rum Romania
rus Russia
slk Slovakia
svn Slovenia
swi Switzerland
tch Czech Republic
ung Hungary
usa USA

Загрузка PDF  FAQ_EN_Updating_cross-section_catalogs_(Allplan_2011...
Версия:  Allplan 2021 / Allplan 2020 / Allplan 2019  | Последнее изменение: 05.11.2020
Not voted yet. Be the first to vote this FAQ as helpful!

Question:
How can I work together on a project with a partner from another country?

Answer:
Using Allplan 2019 and later, you can work on projects across countries.
You can define projects in a country-specific manner. This means that a project gets the resources (for example, hatching, patterns, layers and so on) and reinforcement settings of a specific country. Depending on your license, you can install one or more additional country packages. For example, you can then create a project with resources and settings for Germany and another one with resources and settings for the UK.


Requirements:

Whether you can use country packages depends on the Allplan license.

Only the ‘Cubed’ and ‘Exponential’ license types include country packages.
These license types enable you to use as many country packages as you like. You can create and open projects with any country code.

The ‘Lineared’ and ‘Squared’ license types only include one country package by default. This also applies to all conventional license types such as ‘Architecture’ and ‘Engineering’. In other words, you can only create and open projects with this country code.

Installing country packages:

When installing Allplan 2019 for the first time or upgrading from Allplan 2018 or earlier, you must explicitly install the additional country packages.

A default installation onlyinstalls the country package of your country. If you want to use different country packages, you must do a custom installation. Only a custom installation allows you to select the country packages you want to install.
You can do this whenever you want - be it the first installation or an upgrade or update.

Doing a custom installation:
Start Setup.

Select Customfor the Setup type.
When it comes to selecting Features, you can select the language packages you want to install.
You can see a list of all Allplan languages included in your license.
After this, you can select the countries. Select the country packages you want to install.
Click ‘Next’ to confirm all other dialog boxes.

Note:Please note that the more country packages you select, the longer the installation will take and the more hard disk space will be required.

Using country packages in Allplan:

You must define the country when you create a project. You cannot change the country later.

Creating a new project:
When creating a new project, you can select the county in country-specific templates.
Select the country and the template you need.

If you do not select a project template, you must select the required country in the next dialog box.


In the project:
The status bar shows the country set for a project.
The units for length entries and reinforcement set in the Options are project-specific settings. These units are preset depending on the country selected.



Important note:
  • When checking out a project in a workgroup environment, you can choose which country-specific office standard you want to check out.
  • Click in the ‘License Settings’ to see which countries are included in your license.
  • There is a default country, which is usually the country entered in your license. Setup always installs the data for this default country in the STD and ETC folders. During installation, Setup creates a STD.??? folder and an ETC.??? folder for each additionalcountry package selected (??? stands for the country code). The office path and default path are always based on the country set for the project that is currently open. That is to say, when you open a project and save a favorite or library element in the office path or default path, these elements will only be available in projects with the same country settings. ProjectPilot is an exception; here, the office path and default path always refer to the STD and ETC folders.


Загрузка PDF  FAQ_EN_Country-specific_projects_-_working_together_...
Версия:  Allplan 2018 / Allplan 2017 / Allplan 2016 / Allplan 2015  | Последнее изменение: 22.02.2018
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I copy bar reinforcement including views and sections created with the tools in the "Associative Views" module if, for example, I want to use slab reinforcement for another floor?
I want to place the copied reinforcement and the views in new, separate drawing files and then adjust the reinforcement, keeping the layout of the copied sections. Only the changes in the copied reinforcement should automatically be added to the sections.


Answer:

First, open ProjectPilot (File -> ProjectPilot) and copy the drawing files with the reinforcement and the drawing file with the associative views and sections to new drawing files. ProjectPilot asks you whether you want to copy the linked drawing files as well. Click No.

If there are views or sections containing only data you do not want to move (for example, only model data), select Create -> Engineering Views, Details -> Associative Views -> Add to Viewand add the data you want to move (for example, reinforcement) to these views or sections. You can remove the data later.


The copied drawing files still reference the original drawing files. The next step is to delete those references.

To do this, open the drawing files you just copied. Select Change -> Engineering Views, Details -> Associative Views -> Manage Reference Drawing Filesand remove the references to the source drawing files.



When you have removed all links to drawing files you do not want to move, select the new drawing files with the views and the reinforcement.


Select all data by pressing <CTRL>+A and move the data as you need.
You can move the data in the X, Y and Z directions in plan or define any spatial displacement in isometric view.

You can then add the associated model data to the views and adjust the reinforcement.

Note:

Once deleted, you cannot restore any references to drawing files. Therefore, make sure you delete the right references. Allplan deletes empty views or sections automatically.

Загрузка PDF  FAQ_EN_Copying_reinforcement_with_associative_views_...
Версия:  Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017  | Последнее изменение: 24.10.2019
1 user(s) found this FAQ helpful

Question:

How can I give individual users the right to see and select specific seats on the license server? And how can I deny users this right?
Sometimes, it may be necessary that a specific user does not see the seat with, for example, the terrain option so that this user cannot use this seat inadvertently.


Answer:

Using WebAdmin, you can give users rights for specific seats on the license server.
Please note the following points:

1. Before you start, check that at least CodeMeter Version 6.50 is installed on the license server.
Start CodeMeter Control Centeron the server.
To do this, use the Windows start menu and select CodeMeter -> CodeMeter Control Center. As an alternative, open Search by clicking the Search button on the Start screen. Enter Codemeter and press ENTER. Select Help -> About to see which version of CodeMeter is installed. If the version displayed is older than version 6.50, you must install the latest version of CodeMeter Control Center. Go to the following website
and download the CodeMeter User Runtime for Windowsprogram.

https://www.wibu.com/de/anwendersoftware.html

2. Open WebAdmin. Start CodeMeter Control Centeron the server again.
To do this, use the Windows start menu and select CodeMeter -> CodeMeter Control Center. As an alternative, open Search by clicking the Search button on the Start screen, enter Codemeter and press ENTER. A dialog box opens. Click WebAdminat bottom right.

Or
Enter Localhost:22350in the address bar of your browser.

3. Go to "Configuration -> Server -> License Access Permissions".
Select Mode: Advanced.

4. Go to "Advanced Mode Configuration -> Specific access rules -> Add Firm Code"and select "6000100 - Allplan GmbH". Click Add. "Specific access rules"now inlcude "6000100 - Allplan GmbH".





5. Click "Add Product Code"to select the seat for which you want to define access rights. However, this is only possible if the "Distinction based on Product Item Text" check box is selected.
The "Note" section below in this FAQ lists the abbreviations given at the end of each seat. These abbreviations represent the license contents.
Select the required seat and click "Add" again. Repeat these steps to assign more seats.





6. After having defined the product code, you can now assign an access rule.
By default, all users are allowedto access this seat.
Select the product code you just defined and click "Add new access rule".
Click "User" and enter the required user.
When you click in the field next to "User", you can see all available users with their domain names.
Select the user or enter the user manually. For example, enter DOMAINNAME\SSample and select the right you want to assign to this user by clicking "Allow" or "Deny".

If the default setting is "Allow", you can thus deny users access to the license. If the default setting is "Deny", you can thus allow users to access the license again.
You can add more rules. When you have configured all rules, click "Apply" to apply the changes.

7. You need to restart CodeMeter Service so that the changes take effect.
To do this, select CodeMeter Control Center -> Process -> Stop CodeMeterServiceand then click Restart CodeMeter Service.Before you restart the service, make sure all users have closed Allplan.


Information:

Client access can be defined by one of the following parameters: computer name, IPv4 subnet, user name or group name.
Enter the required parameter in the corresponding field. If you use an active directory, the program auto-completes entries in the "User" and "Group" fields.


Here comes a practical example:

Think about which setting is most useful to you. For example, you have two seats: seat 01 with 7 architecture licenses and seat 02 with 1 architecture license and 1 terrain license. Only two specific users should be able to use seat 02. If you want to deny all other users access to seat 02, you need to add seat 02 to specific access rules and define a rule for this seat 02. First, set the default setting to "Deny". Then, add these two users and select or "Allow" for these users. As a result, all other users can only see seat 01 and these two users can see seats 01 and 02.

However, if you want that these two users can only see seat 02, you need to add both seats to specific access rules and define a second rule for seat 01. Add these two users to this second role and select Deny for these two users. The default setting, which applies to all the other users, is still Allow. As a result, all other users can see seat 01 and these two users can only see seat 02.


Note:

The following abbreviations are used:

T Terrain
B Bamtec
W Workgroup
K Key Plan
M Bridge Modeler
L Cadastral plans for conduits
S Language option
V Visualization
A Architecture option
E Engineering option

Here are some examples:

Architecture:
"Allplan Architecture 2017”

Architecture + Terrain
"Allplan Architecture 2017 T"

Architecture + Bridge Modeler
"Allplan Architecture 2017 M"

Architecture + Terrain + Bridge Modeler
"Allplan Architecture 2017 TM"

Загрузка PDF  FAQ_EN_License_server_-_assigning_access_rights_for_...
Версия:  Allplan 2015 / Allplan 2014 / Allplan 2013 / Allplan 2012 / Allplan 2011  | Последнее изменение: 08.05.2019
2 user(s) found this FAQ helpful

Question:

I have installed Allplan using the temporary Softlock license ("customer#_seat_psd.nslock") and "Trial" is displayed for its status in the License Manager.
How can I register this license?



Answer:

You use License Manager to create a registration request and send it by email to register@nemetschek.de.
In response, you get a final license file. Installing this license removes the lime limit.
Below is a description of the necessary steps.



Notes:

  • Using the temporary license, you can start Allplan as a trial version. You can work with Allplan without any restrictions for 30 days.
    After expiration of this period, Allplan starts as a viewer only. However, you can still request and install the final license.
  • When running Windows Vista, start Nemetschek License Manager as the administrator:
    Start -> (All) Programs -> Nemetschek -> Nemetschek SoftLock 2006 -> License Manager
    Click "License Manager" with the right mouse button and choose "Run as administrator" on the shortcut menu.




How to proceed:

1. Request a license registered for your computer

  1. On the Windows taskbar, click Start - (All) Programs - Nemetschek - Nemetschek Softlock 2006 - License Manager(or Services application -> Utilities -> License -> License Manager (NemSLock)).

    When running Windows Vista, start License Manager as the system administrator: click Start - (All) Programs - Nemetschek - Nemetschek Softlock 2006 - License Manager.
    Click License Managerwith the right mouse button. On the shortcut menu, click Run as administrator.
  2. Select the seat you want to register so that it is highlighted in blue.

    Note:You can only register seats you have purchased. If you can see only seats with numbers between 90 and 99 (= trial licenses for temporary use), you first need to install the personal license for temporary use.
  3. Click License requestat top left.

    The License Request Wizardstarts. The Welcome to the license request wizarddialog box provides information on the steps that follow.
  4. Click Next >.
    The Customer detailsdialog box opens.

    Note: Editing customer details requires administrator privileges. If you do not have these privileges, you will see a corresponding message. Cancel NemSLock License Manager and start again by selecting the Run as administrator option on the shortcut menu.
  5. Enter the necessary details:

    - If the Client IDhas eight zeros (00000000) and the CD Keyhas eight capital F&apos;s (FFFFFFFF), you selected the Trial license for temporary useoption when you installed Allplan.
    In this case, install the personal license for temporary use before you create the registration request.

    - If Client IDand CD Keydo not match the numbers printed on your delivery note (for example, typing errors, small letters and capital letters mixed up), you can enter Client ID and CD Key manually.

    - Fill out all the fields.

    Make sure you enter your email address correctly, because registered licenses and replies to status queries of license will be sent to the address you specify here.

    Note:Check the entries for Client ID(customer number) and CD Key , making sure these numbers are the same as those printed on the delivery note you received from Allplan. The CD Keyusually consists of the numbers 0 to 9 and the capital letters A to F.

    Tip: You can also find these numbers in the personal license file for temporary use (*_psd.nslock). Open the license file in an editor and scroll down to the end of the file. You can then copy the license codes displayed after CUSTOMERand CDKEYto the Clipboard and paste them into the appropriate boxes.
  6. Click Next >.
  7. Select the Program, Versionand Seatand click Next >.

    Note: If the Client IDis invalid (for example, when you use a trial license) you cannot confirm the dialog box by clicking OK. Instead, you will see a corresponding message.
  8. Specify how to send the registration file and click Next >.

    Start email program ...
    The program creates and saves the register.txt file before it opens your default email program. The program automatically attaches the registration file to the email and enters register (please no spam) @ (please no spam) nemetschek.defor the address.

    Save the registration file ...
    The program creates and saves the register.txt file before it opens the folder with the registration file in Windows Explorer. Now you can use all the options provided by Windows Explorer: for example, you can attach the file to an email, copy it to a computer with Internet access and so on.

    In addition, you can see the data that were written to the registration file.
  9. Click Finish.
  10. Click Close to exit NemSLock License Manager.


You will receive a reply by email within a few minutes. This email provides information on the registration process and usually includes the registered license file.

Note: The registered license file is generated by an automated system. Consequently, any additional comments in incoming emails are not read. If you have any questions or need more information, please contact Allplan directly.



2. Install the license file

Shortly after you sent the registration request to &apos;register@nemetschek.de&apos; as described in step 1, the final license file will be sent to the email address you specified in the registration request.
Install this license file as follows:

  • Save the license file to any folder on the hard disk.
    If the license comes as a zip file, extract it.
  • Next, install the license file by double-clicking it ("customer#_seat.nslock").
    Confirm the dialog box.
  • As an alternative, you can also use License Manager to install the license file (Start -> (All) Programs -> Nemetschek -> Nemetschek SoftLock 2006 -> License Manager).
    Click "Install - Install license" at top left in Nemetschek SoftLock License Manager and select the license by clicking "Browse...".
    Click "Finish" to complete the installation process.


Note:

Do not use the same computer to register several license files for different seats. This would connect the seats. You cannot separate the seats again without the help of technical support.

Загрузка PDF  FAQ_EN_Nemetschek_Softlock_-_first_steps.pdf
Версия:  Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016  | Последнее изменение: 23.09.2019
Not voted yet. Be the first to vote this FAQ as helpful!

Question:
I purchased a new license and received a Product Key for Allplan. However, I work with an earlier Allplan version. How can I install and license Allplan 2015 or an earlier version despite the new license?


Answer:

Allplan 2016 introduced a new protection system. Since then licensing has been based on CodeMeter by Wibu Systems AG. You can no longer use Softlock (NemSLock) or hardlocks with Allplan. For running Allplan, you get a Product Key by email. Using this key, you can activate your license online.

This new license is not downward compatible. Consequently, you cannot use it for earlier Allplan versions.

For licensing earlier versions, you require the Client ID and CD Key. You can find this information in the delivery note or invoice. Instead of a temporary license, use the appropriate trial license to install Allplan 2015 or an earlier version. Then generate a registration request to license and activate the modules you purchased.

Note:
If you use a license server for which you purchased an additional license, please read the separate document or contact support.de@allplan.com. We will show you how to add the new license to the license server.

If you want to install Allplan 2015 or an earlier version, use a trial license to install the version you need.

Downloading Allplan:
Make sure the Allplan version you install is always up-to-date. In other words, it should include the latest hotfixes and service releases.
You can download the current Allplan version from Allplan Connect or the FTP server.
Allplan Connect:
https://connect.allplan.com/de/support/downloads.html


1. Install Allplan with a trial license
Install Allplan. In the 'Select License Information' dialog box, choose 'Trial license for temporary use' and select the license for 'Architecture' or 'Engineering'.

Important: If you work with Workgroup Manager, select 'Different trial license' -> 'Next'. Open the Workgroup folder for your country and select the appropriate license. Then follow the instructions and install Allplan. Make sure you enter the paths correctly.


2. Request a license registered for your computer
The trial license is valid for 30 days. It is not personalized.
Consequently, you have to enter your personal data manually when generating the registration request.
You can find the required Client ID and CD Key in the delivery note or invoice.

To generate a registration request, do the following:

Open the License Manager (Service application -> Utilities- > License -> License Manager).
Select the license entry for your seat and click 'Request license'. Please follow the instructions displayed on screen.

Note: Editing customer details requires administrator privileges. The system will issue an appropriate message. Close NemSLock License Manager and start the Services application again. To do this, click the Services desktop icon with the right mouse button and select 'Run as administrator' on the shortcut menu.


Enter the necessary details:
The Client IDhas eight zeros (00000000) and the CD Keyhas eight capital F's (FFFFFFFF).

For the Client ID, enter your customer number. You can find your customer number in the letteror delivery notethat came with Allplan.
For the CD Key, enter your CD Key, which you can also find in the letter or delivery note. Make sure you use small letters and capital letters accordingly.

Note:You can find the Client ID and CD Key at top left in the delivery note. The CD Keyusually consists of the numbers 0 to 9 and the capital letters A to F.


Fill out all the fields. Make sure you enter your email address correctly, because registered licenses and replies to status queries of license will be sent to the address you specify here.
Click Next >

For the seat, change the number 94 to the license you purchased, for example, 02, 03 or 04.
Specify how to send the registration file and click Next >.

Start email program ...
The program creates and saves the register.txt file before it opens your default email program. The program automatically attaches the registration file to the email and enters register (please no spam) @ (please no spam) nemetschek.defor the address.

Save the registration file ...
The program creates and saves the register.txt file before it opens the folder with the registration file in Windows Explorer. Now you can use all the options provided by Windows Explorer: for example, you can attach the file to an email, copy it to a computer with Internet access and so on.

In addition, you can see the data that were written to the registration file.

  1. Click Finish.
  2. Click Close to exit NemSLock License Manager.

You will receive a reply by email within a few minutes. This email provides information on the registration process and usually includes the registered license file.

Note: The registered license file is generated by an automated system. Consequently, any additional comments in incoming emails are not read.


3. Installing the license file
Shortly after we received the registration request, we will send you the final license file to the email address you specified in the registration request.
Install this license file as follows:

  • Save the license file to any folder on the hard disk.
    If the license comes as a zip file, extract it.
  • Next, install the license by double-clicking the license file ("customer#_seat.nslock").
    Confirm the dialog box.
  • As an alternative, you can also use License Manager to install the license file (Start -> (All) Programs -> Nemetschek -> Nemetschek SoftLock 2006 -> License Manager).
    Click "Install - Install license" and then "Browse..." to select the license.
    Click "Finish" to complete the installation process.
  • Your registered license is displayed in the License Manager. Clear the check box for the trial license (for example, seat 94 or 98). Make sure your registered license is the only license that is selected.




Загрузка PDF  FAQ_EN_Installing_an_earlier_version_with_NemSLock_i...
Версия:  Allplan 2020 / Allplan 2019 / Allplan 2018 / Allplan 2017 / Allplan 2016  | Последнее изменение: 23.09.2019
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

I purchased a new license and received a Product Key for Allplan. However, I use earlier Allplan versions with NemSLock server in my office. How can I install Allplan 2015 or an earlier version despite the new license? How can I activate the license on NemSLock server?


Answer:

Allplan 2016 introduced a new protection system. Since then licensing has been based on CodeMeter by Wibu Systems AG. You can no longer use NemSLock server with Allplan. For running Allplan, you get a Product Key by email. Using this key, you can activate your license online.

This new license is not downward compatible. Consequently, you cannot use it for earlier Allplan versions.

If you want to install Allplan 2015 or an earlier version, use a trial license to install the version you need.

Downloading Allplan:
Make sure the Allplan version you install is always up-to-date. In other words, it should include the latest hotfixes and service releases.
You can download the current Allplan version from Allplan Connect or the FTP server.
Downloading from Allplan Connect:
https://connect.allplan.com/de/support/downloads.html

FTP server:
Copy this link and paste it into the address bar of Windows Explorer. Then press ENTER.
ftp://nemhotline:ha37jvg8f@ftp.nemetschek.de
This opens the folder on our FTP server.

Go to /download/Allplan/2015/CD (choose the path in accordance with the version you need) and select the appropriate file. Then click Edit -> Copy (Ctrl+C).
Switch to a folder on your computer and select Edit -> Paste (Ctrl+V).
Extract the ZIP file. Right-click the EXE file and select "Run as administrator".
Deactivate the virus scanner during installation.


1. Install Allplan with a trial license
Install Allplan. In the 'Select License Information' dialog box, choose 'Trial license for temporary use' and select the license for 'Architecture' or 'Engineering'.

Important: If you work with Workgroup Manager, select 'Different trial license' -> 'Next'. Open the Workgroup folder for your country and select the appropriate license. Then follow the instructions and install Allplan. Make sure you enter the paths correctly.


2. Use NemSLock server to request a registered license for the new seat

If you have not used a license server until now, install the license server using the trial license for NemSLock Server.

Installing NemSLock Server

  • Start the Setup program for NemSLock Server. You can find the latest Setup program on our FTP server:

ftp://nemhotline:ha37jvg8f@ftp.nemetschek.de/download/Allplan/Lizenzserver/2014/allplan2014-nemslock-lizenz.zip

  • The trial license is also on the FTP server:

ftp://nemhotline:ha37jvg8f@ftp.nemetschek.de/download/Allplan/Lizenzserver/Allplan 2015 Nemslock Server Trial.nslsrv

  • Select the trial license file for NemSLock Server. This license is valid for 30 days, but it includes only seat. The full number of seats purchased will be available to you as soon as you have installed the registered licenses (see below).
  • Select the full installation.
  • If the service does not start automatically after Setup, select Control Panel -> Administrative Tools -> Services and start the Nemslock Server 2006 service.



Registering licenses

  • Open NemSLock 2006 Server Consoleby clicking the corresponding icon on the desktop or by selecting Start -> All Programs -> NemSLock 2006 Server -> NemSLock 2006 Server Console.
  • Switch to Moduleson the left.
  • Select one of your seats.
  • Click the Registration request (register.txt)button.
  • Click Edit.
  • Fill out all fields marked with an asterisk (*). Make sure you enter your email address correctly, because the registered license file will be sent to this address (and not to the address of the person who sent the registration request!). Click OKto confirm.
  • Click Create registration request. Windows Explorer opens and shows the register.txt file.
    If you have closed Windows Explorer, you can find the file in the program folder of NemSLock Server. If you installed the program to the path proposed, the path is
    C:\Program Files (x86)\Nemetschek\NemSLock Server 2006\Programs\License.
  • Use an editor to open the new register.txt file.

You can find the entry for your seat in line @23@seat:. Change it and enter your new seat number instead. For example, if you purchased seat 08, change the entry to @23@seat: 08. Save the file.

  • You can now use all the options provided by Windows Explorer to copy the registration file to a computer with Internet connection. You can do this on the network or you can use a USB stick. You can then email the file to us.
  • Send the email with the registration request to register@nemetschek.de.
  • You will promptly receive your registered license for the new seat.



Installing licenses
Exit Allplan on all workstations.

  • Open NemSLock 2006 Server Console.
  • Click Stop serveron the left.
  • Switch to Moduleson the left.
  • Click Browse and select the registered license file.
  • Click Install license file.
  • After this, you can start the server again by clicking Start server.



Note:

If you purchased several new licenses, you have to generate and send a separate registration request for each seat. Just repeat the steps described above. You will then receive a registered license file for each seat. You must install each file.

Загрузка PDF  FAQ_EN_Installing_an_earlier_version_with_NemSLock_s...
Версия:  Allplan 2018 / Allplan 2017  | Последнее изменение: 01.11.2017
Not voted yet. Be the first to vote this FAQ as helpful!

Question:

How can I use data from the "Shell" module in Allplan 2017 and later?



Answer:


Data conversion in Allplan 2017

Allplan 2017automatically converts shell data from earlier versions the first time you open the project or *.ndw file in question.

Alllayouts you created ofgeneral arrangement drawings and reinforcement drawings stay as they are!
The 3D reinforcement modelstays as it is!
Theshell entitybecomes a 3D solid.
The views and sections(including reinforcement) become 2D elements and text.

Editing the data

As the old shell entitybecomes a 3D solid(construction lines) and the 3D reinforcement model stays as it is, you can create new associative views and sections from the model data.
Before you can do this, you need to assign "normal" format properties to the 3D solid created from the shell entity, as you cannot create associative views and sections from a solid in construction line format.

You canplace, modify and labelthe reinforcement without any restrictions. You can create schemas, legends andreportsas usual.




Загрузка PDF  FAQ_EN_Shell_module_no_longer_available.pdf
1 - 8 (8)
  • 1
https://campus.allplan.com/ uses cookies  -  More information

Accept