Das Wissen aller Anwender nutzen

Im Allplan Connect Forum tauschen sich Anwender aus, geben wertvolle Tipps oder beraten sich bei ganz konkreten Aufgabenstellungen − auch international.
Und damit wirklich keine Frage unbeantwortet bleibt, unterstützen die Mitarbeiter des Technischen Supports ebenfalls aktiv das Forum.

Es erwarten Sie:

  • Foren-Vielfalt aus CAD Architektur, CAD Ingenieurbau uvm.
  • Tipps von User für User
  • international: Deutsch, Englisch, Italienisch, Französisch und Tschechisch

Melden Sie sich jetzt an und diskutieren Sie mit!

Zur Registrierung

[Frage] Dimension the floor and ceiling covering in Section [Gelöst]

Schlagworte:
  • Sections & Views Architecture
  • Room
  • Floor covering
  • Ceiling covering
brugyo
brugyo
27.03.2019 - 11:23

Hi everybody,

I would like to dimension the floor covering and the ceiling covering in the room. How can I do this?

Thanks,
György

Anhänge (1)

img
section_floor_ceiling_covering.png
Typ: image/png
44-mal heruntergeladen
Größe: 61,15 KiB

Lösung anzeigen Lösung verbergen

pasqua_enzo
pasqua_enz…
28.03.2019 - 13:36 *

Ok. Try to remove the check on "udate automatically" inside the section properties. It should work.

Ingegnere Edile | 3D Artist | BIM expert

Tel: +393463266095
Skype: pasqua.enzo
Website: http://www.enzopasqua.com
LinkedIn: http://www.linkedin.com/in/enzopasqua
Instragram: http://www.instagram.com/enzopasqua3d/
PEC: enzo.pasqua (please no spam) @ (please no spam) ingpec.eu

pasqua_enzo
pasqua_enz…
27.03.2019 - 15:50 *

Ciao Gyorgy. You mean horizontal quote in plan?

Ingegnere Edile | 3D Artist | BIM expert

Tel: +393463266095
Skype: pasqua.enzo
Website: http://www.enzopasqua.com
LinkedIn: http://www.linkedin.com/in/enzopasqua
Instragram: http://www.instagram.com/enzopasqua3d/
PEC: enzo.pasqua (please no spam) @ (please no spam) ingpec.eu

brugyo
brugyo
28.03.2019 - 10:49

Hi Enzo,

I don't understand exactly what you mean, but I would like to dimension the floor covering and the ceiling covering in section with vertical dimension.

Thanks,
György

Anhänge (1)

img
floor covering_section.png
Typ: image/png
32-mal heruntergeladen
Größe: 33,27 KiB
pasqua_enzo
pasqua_enz…
28.03.2019 - 11:06 *

Sorry Gyorgy. Now I understood. Try to use instead a point in the middle of the line the point in the angle between the wall and the slab. The snap might work there.

Ingegnere Edile | 3D Artist | BIM expert

Tel: +393463266095
Skype: pasqua.enzo
Website: http://www.enzopasqua.com
LinkedIn: http://www.linkedin.com/in/enzopasqua
Instragram: http://www.instagram.com/enzopasqua3d/
PEC: enzo.pasqua (please no spam) @ (please no spam) ingpec.eu

brugyo
brugyo
28.03.2019 - 12:36

Hi,

unfortunately, this isn't work.

pasqua_enzo
pasqua_enz…
28.03.2019 - 13:36 * [Lösung]

Ok. Try to remove the check on "udate automatically" inside the section properties. It should work.

Ingegnere Edile | 3D Artist | BIM expert

Tel: +393463266095
Skype: pasqua.enzo
Website: http://www.enzopasqua.com
LinkedIn: http://www.linkedin.com/in/enzopasqua
Instragram: http://www.instagram.com/enzopasqua3d/
PEC: enzo.pasqua (please no spam) @ (please no spam) ingpec.eu

brugyo
brugyo
01.04.2019 - 09:05

Hi,

Thanks!!!!
Why should I turn off the "update automatically"?

György

pasqua_enzo
pasqua_enz…
01.04.2019 - 10:50

Cause if you switch it the finitures become a 2d design and the snaps work. After designing your quote you switch this parameter on and you have the initial situation.

Ingegnere Edile | 3D Artist | BIM expert

Tel: +393463266095
Skype: pasqua.enzo
Website: http://www.enzopasqua.com
LinkedIn: http://www.linkedin.com/in/enzopasqua
Instragram: http://www.instagram.com/enzopasqua3d/
PEC: enzo.pasqua (please no spam) @ (please no spam) ingpec.eu